Professional heating, cooling & air quality services serving Johnston and surrounding communities in Iowa. NATE-certified, 24/7 emergency response.
From emergency repair to planned installation, we deliver expert HVAC service across every specialty.
Clogged dryer vents are a leading cause of residential fires, with lint buildup restricting exhaust airflow and causing the dryer to overheat. Professional cleaning removes compacted lint from the full vent run, verifies proper airflow velocity, and inspects the exterior termination for damage.
Scheduling professional furnace maintenance each fall ensures your heating system delivers full BTU output without wasting fuel. Technicians inspect the inducer motor, verify pressure switch operation, calibrate gas valve output, and clean the burner assembly for reliable cold-weather performance.
Installing a mini-split system correctly requires precise wall penetration, vacuum-sealed refrigerant lines, and proper electrical isolation between indoor and outdoor units. Our technicians size each zone independently using BTU calculations to ensure consistent temperature control across every room.
Boiler systems demand specialized knowledge of hydronic circuits, expansion tanks, pressure relief valves, and combustion analysis. Our technicians diagnose issues ranging from kettling and low water pressure to faulty zone valves and circulator pump failures across gas, oil, and electric units.
Heat pumps rely on a precise balance of refrigerant pressure, electrical components, and airflow to deliver efficient heating and cooling year-round. Professional repair addresses compressor hard starts, frozen coils, faulty thermostatic expansion valves, and auxiliary heat lockout conditions.
Comprehensive HVAC inspections cover thermostat operation, ductwork condition, refrigerant levels, electrical connections, and combustion safety. This detailed assessment identifies efficiency losses, safety hazards, and components nearing end of service life before they result in costly emergency repairs.
Full HVAC installation requires coordination of heating equipment, cooling components, ductwork design, and control systems to deliver efficient comfort at rated capacity. Our technicians perform Manual J and Manual D calculations, size equipment to match your structure, and commission the system to manufacturer standards.
Professional AC tune-ups follow a multi-point inspection protocol covering thermostat calibration, condensate drain clearing, electrical connection tightening, and evaporator coil cleaning. Maintaining clean coils and proper superheat readings keeps your system running at peak rated efficiency.
Indoor air quality suffers when ductwork harbors years of accumulated particulate matter, allergens, and biological growth. Thorough duct cleaning addresses every branch run, main trunk line, and register boot using agitation tools and high-powered vacuum extraction to restore clean airflow.
Ductwork problems manifest as uneven room temperatures, excessive dust near registers, and HVAC systems that run continuously without satisfying the thermostat. Technicians identify crushed flex runs, separated joints, and deteriorated mastic seals using pressure testing and visual inspection protocols.
Upgrading to a smart thermostat enables precise scheduling, remote access, and energy usage reporting that can reduce heating and cooling costs by 10 to 15 percent. Professional installation ensures correct wiring to your HVAC system, including C-wire verification and multi-stage equipment compatibility.
A correctly sized heat pump installation eliminates the guesswork of mismatched equipment and undersized ductwork. Our technicians perform load calculations, verify airflow across the evaporator coil, and commission the system to manufacturer specifications for peak efficiency and longevity.
When your AC blows warm air, short cycles, or fails to start, the problem may involve a failed compressor, low refrigerant charge, frozen evaporator coil, or faulty control board. Professional repair identifies the exact fault and restores rated SEER efficiency through precise, manufacturer-guided procedures.
Ductless mini-split systems require specialized diagnostics for inverter-driven compressors, electronic expansion valves, and multi-zone communication boards. Our technicians resolve issues including refrigerant leaks at flare connections, blinking error codes, frozen evaporator coils, and failing fan motors.
When your heating or cooling system fails unexpectedly, rapid diagnosis is critical to minimizing discomfort and preventing secondary damage like frozen pipes or heat-related illness. Emergency technicians isolate the fault, whether electrical, mechanical, or refrigerant-related, and execute repairs on the spot.
Johnston, IA is home to 25,537 people and a wide variety of heating and cooling systems — from central forced air to radiant boilers to ductless mini splits. KIC Refrigeration has worked on every HVAC configuration across the Johnston area. That hands-on experience means we know exactly which equipment brands and installation methods deliver the best performance in this region.
Our familiarity with Johnston extends beyond HVAC equipment — we understand the neighborhoods, the local permitting process, and the seasonal weather patterns that stress every heating and cooling system in the area. When KIC Refrigeration takes on your project, you benefit from a team that factors in your home's age, insulation quality, and duct layout before recommending a single piece of equipment.
What makes us different from every other heating and cooling company in the area.
You receive a written estimate with itemized parts and labor costs before any work begins, and the final invoice matches. No diagnostic fees hidden in the repair bill, no surprise surcharges — just honest pricing you can verify and trust.
HVAC failures do not wait for business hours and neither do we. Our emergency technicians are dispatched around the clock — nights, weekends, and holidays — so you never go without heat in winter or cooling in the peak of summer.
Every technician on our team holds current NATE certification — the highest standard in the HVAC industry for installation and service competency. You get a technician who has passed rigorous exams on system diagnostics, refrigerant handling, and equipment commissioning.
We help you select equipment with the highest SEER2, HSPF2, and AFUE ratings that fit your budget, and we install it to manufacturer specifications so you actually achieve rated efficiency. Proper charge, proper airflow, proper duct sealing — the details that turn rated efficiency into real savings.
If the repair does not solve the problem or the installation does not perform to specification, we come back and make it right at no additional cost. Our guarantee covers workmanship, parts, and system performance because half-finished work is not in our vocabulary.
Common questions about HVAC service, costs, and what to expect when you call.
Yes. KIC Refrigeration provides around-the-clock emergency heating and cooling repair throughout Johnston and surrounding Iowa communities. Whether your furnace fails during a cold snap and pipes are at risk of freezing, your air conditioner dies during a dangerous heat wave, or you detect the smell of gas near your equipment, our technicians respond quickly. Every service vehicle carries common replacement parts — capacitors, contactors, ignitors, blower motors, control boards, and refrigerant — so most emergency repairs are completed in a single visit. We do not charge extra trip fees for after-hours calls, and our dispatchers are trained to triage situations over the phone so the right technician arrives with the right equipment. Call us anytime and we will have a crew on the way.
Heat pumps offer both heating and cooling from a single outdoor unit, making them significantly more energy-efficient than furnaces for moderate climates. A heat pump does not generate heat — it transfers it from outdoor air, which requires far less energy than burning gas or running electric resistance coils. Modern cold-climate heat pumps with variable-speed inverter compressors operate effectively down to minus 15 degrees Fahrenheit, making them viable in most Iowa locations. For Johnston homeowners with natural gas access, a dual-fuel system — heat pump for primary heating paired with a gas furnace for backup during extreme cold — often provides the best balance of efficiency and performance. Heat pumps also qualify for federal tax credits under the Inflation Reduction Act. KIC Refrigeration evaluates your specific climate zone, insulation levels, and utility rates to determine whether a heat pump, furnace, or dual-fuel system is the smartest investment.
Most residential HVAC installations in Johnston, IA are completed in 1 to 3 days depending on the system type, condition of existing ductwork, and complexity of the project. A straightforward furnace and air conditioner replacement on existing ductwork typically takes a single day — our crews arrive in the morning and commission the new system by afternoon. Heat pump conversions, ductless multi-zone installations with line sets routed through walls, and projects requiring new or modified ductwork may take 2 to 3 days. Commercial installations and whole-building systems can extend to a week. We schedule around your availability, coordinate all permits and inspections, and protect your flooring and walls throughout the process. Every installation concludes with a full system commissioning including airflow verification and refrigerant charge confirmation.
Yes. KIC Refrigeration offers flexible financing options for HVAC installations in Johnston, IA, including low-interest plans, deferred interest same-as-cash programs, and extended payment terms that make it easier to invest in high-efficiency equipment without a large upfront cost. Approved applicants can often finance a complete system replacement for less than $100 per month. We also help Johnston homeowners identify and apply for available financial incentives including utility company rebates on high-efficiency equipment, manufacturer promotional pricing, and federal tax credits such as the 25C Residential Clean Energy Credit which provides up to $2,000 for qualifying heat pump installations and up to $600 for qualifying furnaces and air conditioners. Between financing, rebates, and tax credits, the effective cost of a new high-efficiency HVAC system is often significantly lower than the sticker price.
A comprehensive HVAC inspection from KIC Refrigeration in Johnston covers every critical component of your heating and cooling system. Our NATE-certified technician evaluates the heat exchanger for cracks using a combustion analyzer, checks thermostat calibration and wiring, tests all electrical connections for tightness and amperage draw, measures refrigerant pressures against manufacturer specifications, clears the condensate drain line, inspects the blower motor and fan assembly for wear, checks the air filter and evaporator coil condition, tests safety controls including high-limit switches and flame sensors, performs carbon monoxide testing on gas-burning equipment, and measures supply and return airflow temperatures to verify the system is producing its rated BTU output. We also visually inspect accessible ductwork for leaks, damage, and insulation condition. You receive a written report with all findings, photos of any concerns, and prioritized recommendations.
Absolutely. Modern high-efficiency HVAC equipment can reduce heating and cooling costs by 20 to 40 percent compared to systems installed 15 or more years ago. The improvement comes from advances in compressor technology, variable-speed motors, and smarter controls. In Johnston, upgrading from a 10-SEER air conditioner to a 16-SEER2 or higher unit delivers substantial monthly savings — the higher the SEER2 rating, the less electricity consumed per BTU of cooling. On the heating side, replacing an 80-percent AFUE furnace with a 96-percent modulating furnace means that 16 cents of every heating dollar previously wasted up the flue now heats your home. Heat pumps offer even greater efficiency, delivering 2 to 4 times more heating energy than they consume in electricity. KIC Refrigeration calculates projected energy savings for any equipment upgrade so you can see the return on investment before making a decision.
Our reputation is built on honest service, skilled technicians, and systems that perform.
"KIC Refrigeration is the only HVAC company I will use going forward. They have done our furnace maintenance for three years without a single issue."
"KIC Refrigeration has serviced our commercial HVAC system for two years now. Always professional, always on time. Would not trust anyone else."
"Mini split installation went smoothly. Clean work, no mess left behind. Would have liked a bit more explanation on the maintenance schedule but overall very happy."
We also serve these nearby communities with the same certified HVAC expertise.